Capybara Phone Holder / Keyring

Capybara Version v1.3 - 07 VII 2025 There is a front (head in front of the screen) and reversed (head behind phone) model and a full model without a hole for a phone Additionally there are keyring addons (to front or back) that you can use with a desired Capybara model In files there are also V11.zip and V12.zip files with older version of capybara if you liked it more More about changes on the bottom in Updates section --- If you want to sell prints of this models you can buy a Commercial License here: https://cults3d.com/en/3d-model/gadget/capybara-phone-holder-keyring-commercial-license Check Phone Collection for more models https://www.printables.com/@C47_3d/collections/793008 --- Printing Timelapse of 3 capybaras https://www.instagram.com/p/Cv1zEdfNVQ- --- Number in file names is a space for a phone in mm For phone thickness of 8-16mm - they are also on the bottom of models to show what size it is after print To resize the models use the equasion: 'Needed space (in milimeters)' divided by 'model number' multiplied by 100% = 'Needed model size in percent' For example if you need more stable 16mm you can take 10mm version resized to: 16 / 10 * 100% = 160% May not be suitable for phone set vertically but it depends on phone size and its weight The smaller the gap between the print and a phone the better chance it will not fall Reversed version may be better for this You can also resize smaller version to the bigger size Version 1.3 is longer and with smaller phone angle so it will be more stable than older models The gap is cut with 12dgr angle (previously 16dgr) --- To make a keyring use a Capybara model of your choice and add there a keyring model (back or front). Version for back can be moved to different place and rotated (for example if you want it on side of capybara) Then merge both models - see a screen from Cura and PrusaSlicer on the last photo Keyring models are with a 'frame', a flat surface that will not be printed. This way it is easy to set it in the right spot with a Capybara - Ignore model 'errors' and DO NOT try to 'fix' the model Solid version of Capybara (without a hole for a phone) is with a sepparate files that are already with a keyring CapybaraV13-keyring-back CapybaraV13-keyring-front CapybaraV13-long is a longer version, the same as used for phones It's compatible with keyring addons --- HOLES version Models are for a filament string used as eyes - usually a black one Push it in with a pliers, then cut it with cutting pliers or a knife (be carefull to not damage the print or yourself) Then you can use some a heatgun, small torch or a lighter to smooth the cutted end To make it on phone version models add CapybaraV13_eyes-holes-negative-volume as a negative volume (right click on model) --- Update 16 VIII 2023 Small change to sides and back of the model. Will be easier to print and use with a kechain Added keychain models Update 29 VIII 2023 Changed from versions 12-16mm to 10-15mm with more precise angles You can resize the model for different phone thickness Angle changed from ~16,5dgr to 16dgr Update 31 VIII 2023 Changed Keyring-back addon. Looks and works better Added photos of a new keyring print UPDATE 06 I 2024 Added versions for 6-9mm phones UPDATE 05 IV 2024 Added numbers on the bottom of models to show what size it is after print Added 'mm' to file names to avoid rare confusions Added version for 16mm phone Changed keyring addons a little (should be stronger) Changed 'C47_3D' on the bottom for easier printing UPDATE 14 IV 2024 - V1.2 Reshaped some details of a Capybara for a nicer print (better angles so there will be less stair-like layers ). Also the model is little cleaner, especially in the bottom PHONE versions are longer and with a hole that starts from a lower position - this way it is more stable and can be used with a phone set vertically with much more smartphone models Reversed version holes now starts from the same position on the back - so now no matter what size version you will print it will look the same with a smartphone Added HOLES version to use a filemant string as eyes Keyring_back is longer - so more space for a ring and even more stability Keyring_front is changed and moved more to front for more space for a ring UPDATE 07 VII 2025 - V1.3 Changed phone angle from 16dgr to 12dgr for better stability Changed keyring on the back. Different design, should be stronger Removed HOLES versions. Now you can make it with CapybaraV13_eyes-holes-negative-volume - so there is much less files now --- Print Settings Printed with 0.4mm nozzle NO supports needed 0.1-0.2mm layer height 2-3 walls 7% gyroic infill - just for little stronger print and better stability (will be more heavy) ---